GE dryer
showing Clean Filter
Clean Filter is a status light telling you it is time to clear the lint filter.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: GE
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Clean Filter
actually means.
Clean Filter is a status light telling you it is time to clear the lint filter. It is a maintenance prompt built into the display, not a report of a broken part.
GE dryer display
What to do when Clean Filter shows on the dryerKind of codeMode, not a failure
A setting someone switched on, or a prompt the dryer shows by design — a child lock, a clean-the-lint-screen reminder, a demo setting. Nothing has failed and no part is needed.
Usually leads toNo repair
Pull out the lint filter and wipe off the lint with moistened fingers.
Shows up asDryer Not Starting
The panel lights up and responds, but pressing start does nothing or only makes a hum.
MakeGE
Widely sold dryers in electric and gas versions, as standalone machines, stacked pairs and single-unit laundry centers.
SourceGE Appliances compact dryer owner's manual 49-3000311 (GFT14)
GE compact dryers (GFT14 family) with a status display.
Before you book,
in this order.
Each step comes from GE's own guidance for Clean Filter on its dryers. Follow it to the end: the last card says whether this is a visit.
Pull out the lint filter and wipe off the lint with moistened fingers.
Slide it back fully; the dryer should never run without it.
If drying stays slow with a clean filter, check the condenser box.
Cleared?
No part needed replacing. If the next full load still comes out damp or the dryer shuts off early, treat that as a separate problem.
What not to do
The light does not mean the filter is damaged. Only a torn screen needs replacing.
What you may
notice with it.
The dryer problems Clean Filter tends to arrive with. Answer these at the dryer before anyone is booked.
All problems
No repair indicated
Nothing to repair.
A setting someone switched on, or a prompt the dryer shows by design — a child lock, a clean-the-lint-screen reminder, a demo setting. Nothing has failed and no part is needed.
GE
dryers.
Widely sold dryers in electric and gas versions, as standalone machines, stacked pairs and single-unit laundry centers.
GE dryer repairMore GE codes
Mode, not a failure on other makes
Electric dryer
The most common dryer in US homes: a 240-volt heating coil, a belt-driven drum and a vent to the outside.
Gas dryer
Heat from a burner on natural gas or propane, lit by an igniter and watched over by a flame sensor, with the motor on 120 volts.
Stackable dryer
The dryer half of a stacked pair or a single-frame laundry center, where the height and the closet decide how the repair is done.
In GE's own words
Time to clean the filter. See the Care and Cleaning section.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE compact dryers (GFT14 family) with a status display.
GE Clean Filter dryer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Clean Filter.
Can I clear Clean Filter myself?
How often does Clean Filter come on for a GE compact dryer?
Can I run my GE compact dryer without the filter while it dries?
Back to your everyday
Still showing Clean Filter?
Book with the code exactly as displayed, the whole model number, and whether you smell burning or gas — for a code, that is where the diagnosis starts.