GE Profile dryer
showing Pause
Pause on the display, with the Start/Pause light flashing, means the cycle was paused, usually by a second press of Start.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Pause
actually means.
Pause on the display, with the Start/Pause light flashing, means the cycle was paused, usually by a second press of Start. Pressing Start again carries on where it stopped.
GE Profile dryer display
What to do when Pause shows on the dryerKind of codeMode, not a failure
A setting someone switched on, or a prompt the dryer shows by design — a child lock, a clean-the-lint-screen reminder, a demo setting. Nothing has failed and no part is needed.
Usually leads toNo repair
Make sure the door is fully closed.
Shows up asDryer Not Starting
The panel lights up and responds, but pressing start does nothing or only makes a hum.
MakeGE Profile
GE's upper line of dryers, in electric and gas versions with more electronic controls and drying options.
SourceGE Profile dryer owner's manual 49-3000244 (linked from PTD90EBPTRS support)
GE Profile dryers with a text display (PTD90 family).
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Pause on its dryers. Follow it to the end: the last card says whether this is a visit.
Make sure the door is fully closed.
Press Start to resume the cycle.
If Pause returns without anyone touching the panel, book a visit.
Cleared?
No part needed replacing. If the next full load still comes out damp or the dryer shuts off early, treat that as a separate problem.
What not to do
Pause is not a code that needs clearing. Nothing has failed.
What you may
notice with it.
The dryer problems Pause tends to arrive with. Answer these at the dryer before anyone is booked.
All problems
No repair indicated
Nothing to repair.
A setting someone switched on, or a prompt the dryer shows by design — a child lock, a clean-the-lint-screen reminder, a demo setting. Nothing has failed and no part is needed.
GE Profile
dryers.
GE's upper line of dryers, in electric and gas versions with more electronic controls and drying options.
GE Profile dryer repairMore GE Profile codes
Mode, not a failure on other makes
Electric dryer
The most common dryer in US homes: a 240-volt heating coil, a belt-driven drum and a vent to the outside.
Gas dryer
Heat from a burner on natural gas or propane, lit by an igniter and watched over by a flame sensor, with the motor on 120 volts.
Stackable dryer
The dryer half of a stacked pair or a single-frame laundry center, where the height and the closet decide how the repair is done.
In GE Profile's own words
The Start/Pause light will flash and the message “Pause” will show in the display
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile dryers with a text display (PTD90 family).
GE Profile Pause dryer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Pause.
Can I clear Pause myself?
My GE Profile shows Pause and won't restart. What am I missing?
Does Pause on a GE Profile reset the cycle time?
Back to your everyday
Still showing Pause?
Book with the code exactly as displayed, the whole model number, and whether you smell burning or gas — for a code, that is where the diagnosis starts.