Whirlpool dryer
showing F6 E1
F6 E1 is a communication error between the main control board and the user interface, the touchpad on the console.
Mon–Sat, 8am–8pm
- Communication
- Controls and sensors
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F6 E1
actually means.
F6 E1 is a communication error between the main control board and the user interface, the touchpad on the console. The trouble can be either board or the wiring that joins them.
Whirlpool dryer display
What to do when F6 E1 shows on the dryerKind of codeCommunication
The main control board and the display board have stopped talking to each other. The harness and its connectors are checked before either board.
Usually leads toControls and sensors
A blank display, a panel that ignores buttons, codes, or cycles that end too soon or never end, traced to the board, timer or sensors.
Shows up asDryer Control Panel Not Responding
Buttons do nothing, the dial turns without effect, or the display is frozen or flickering.
MakeWhirlpool
One of the most common dryer brands in American homes, in electric and gas versions and stacked laundry centers.
SourceWhirlpool product help: F6 E1 communication
Whirlpool dryers with an electronic touchpad and a two-part F/E display.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F6 E1 on its dryers. Follow it to the end: the last card says whether this is a visit.
Turn the breaker off for one minute, then back on.
Start a Timed Dry cycle and watch the display for a minute.
If the code returns, book a visit so the harness and both boards can be checked.
What not to do
An unresponsive panel with no code at all is often the control lock, which Whirlpool shows as Loc rather than F6 E1.
What you may
notice with it.
The dryer problems F6 E1 tends to arrive with. Answer these at the dryer before anyone is booked.
All problems
Dryer Control Panel Not Responding
5 causes, cheapest first
Where F6 E1 usually leads
Controls and sensors.
Whirlpool
dryers.
One of the most common dryer brands in American homes, in electric and gas versions and stacked laundry centers.
Whirlpool dryer repair
Electric dryer
The most common dryer in US homes: a 240-volt heating coil, a belt-driven drum and a vent to the outside.
Gas dryer
Heat from a burner on natural gas or propane, lit by an igniter and watched over by a flame sensor, with the motor on 120 volts.
Stackable dryer
The dryer half of a stacked pair or a single-frame laundry center, where the height and the closet decide how the repair is done.
In Whirlpool's own words
There may be a problem with the Main Control Board, the User Interface (Touchpad), or the associated wiring.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool dryers with an electronic touchpad and a two-part F/E display.
Whirlpool F6 E1 dryer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F6 E1.
Can I clear F6 E1 myself?
Does F6 E1 mean my Whirlpool needs a new control board?
What should I try before booking a visit for F6 E1 on my Whirlpool?
Back to your everyday
Still showing F6 E1?
Book with the code exactly as displayed, the whole model number, and whether you smell burning or gas — for a code, that is where the diagnosis starts.