Dryer
Control Board and Moisture Sensor Repair
A blank display, a panel that ignores buttons, codes, or cycles that end too soon or never end, traced to the board, timer or sensors.
Mon–Sat, 8am–8pm
- Moderate cost band
- 4 steps on the visit
- 5 problems it answers
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
What the dryer control board and moisture sensor repair
involves.
A dryer decides when clothes are done in one of two ways: a mechanical timer with a thermostat, or a dryer control board reading the moisture sensor bars inside the drum and a thermistor in the airflow. The sensor bars are two metal strips the wet clothes touch, and a film of softener residue on them makes the dryer think a wet load is dry. Many control complaints are that film, a loose harness or a door switch, so the board is tested against its inputs before anyone replaces it.
How the visit goesWhat it usually costsModerate · Control board, timer or moisture sensor
Priced against the model, and tested against its inputs first, since dirty sensor bars imitate a failed board.
Answers 5 problemsDryer Control Panel Not Responding
Dryer Error Code · Dryer Not Turning On · Dryer Stops Mid-Cycle · Dryer Takes Too Long to Dry
Comes up most onElectric dryer
Gas dryer · Stackable dryer · Ventless dryer
Codes that lead hereE0 · E1 · E2 · E 4
Asko dryer showing E0.
Controls and sensors,
step by step.
Replace the failed board, timer, keypad or sensor and run a sensor dry cycle on a real load.
Read any stored code or run the service test where the model has one, and treat it as a lead to confirm.
Clean and test the moisture sensor bars and check the thermistor reading against the actual air temperature.
Check the harness, the power supply to the board and the door switch input before condemning the board or timer.
Replace the failed board, timer, keypad or sensor and run a sensor dry cycle on a real load.
The problems
it answers.
5 of them, from dryer control panel not responding to dryer takes too long to dry.
All problems
Dryer Control Panel Not Responding
5 causes, cheapest first
Before you call
Tell us this when you book
- The code or light pattern on the display
- Whether cycles end with clothes still damp
- Whether the buttons respond at all
- Whether there was a storm or a power outage recently
It also answers
Moderate,
on the site's scale.
Priced against the model, and tested against its inputs first, since dirty sensor bars imitate a failed board.
Read the full cost guide| Repair | Relative cost |
|---|---|
| Vent cleaning and inspection | |
| Door switch, catch or hinge | |
| Thermal fuse or thermostat | |
| Heating element | |
| Igniter, flame sensor or gas valve coils | |
| Drum belt, idler pulley, rollers or glides | |
| Control board, timer or moisture sensor | moderate |
| Condensate pump, condenser or heat-pump system | |
| Drive motor or blower wheel |
Where it
comes up most.
Most bookings: Electric dryer, Gas dryer, Stackable dryer, Ventless dryer.
All dryer typesCodes that lead here
E0ASKO · CommunicationE 4Electrolux · Sensor circuitE1Kenmore · Sensor circuittE1LG SIGNATURE · Sensor circuit
Often the same visit
The makes
we see it on.
14 makes on this site, and the dryer control board and moisture sensor repair on any of them. Each mark opens that make's own page.
All 14 brandsControls and sensors,
where we come out.
The laundry room, the climate and the building all change how the dryer control board and moisture sensor repair goes. These notes are about that, metro by metro.
All service areasTampa BayFL · 31 areas
Summer storms and outages are part of life around Tampa Bay, and a dryer with a blank panel afterward is checked at the breaker and the outlet before anyone suspects the electronics.
OrlandoFL · 30 areas
Orlando's newer dryers use moisture sensor bars to end the cycle, and fabric softener residue on those bars is a common reason a load stops early and comes out damp.
Miami / South FloridaFL · 47 areas
Electronic dryer controls in humid Miami closets can throw intermittent errors that come from damp or corroded connectors, so the wiring harness plugs are cleaned and reseated first, and a new board comes last.
New York MetroNY · 75 areas
Compact and ventless dryers common in New York apartments lean heavily on sensors, and a cycle that seems to run forever is often a moisture sensor or thermistor reporting the wrong reading rather than a heating problem.
HoustonTX · 36 areas
After a Houston storm, a dryer that powers up but shows an error may have a loose thermistor connection or a board that took a surge, and the error is read and the sensor circuit tested before any board is ordered.
ChicagoIL · 50 areas
In older Chicagoland homes a dryer may share a circuit or plug into an aging receptacle, and a control panel that resets or shows errors is checked for supply problems before the board is blamed.
Los AngelesCA · 95 areas
Newer Los Angeles dryers with touch panels and connected features can display errors that point to a sensor rather than the control itself, and reading the code first avoids replacing a board that was never the problem.
San DiegoCA · 31 areas
A San Diego dryer control that stops responding is often in a garage exposed to coastal damp, and the panel connections and thermistor plug are checked for corrosion before any electronics are replaced.
San Francisco Bay AreaCA · 74 areas
Heat-pump and newer electric dryers in the Bay Area rely on more sensors than older machines, and a control error is often traced to a thermistor or a clogged filter the software has noticed.
Questions about
the dryer control board and moisture sensor repair.
Why does the sensor dry cycle stop while clothes are still damp?
My dryer display is completely blank. Is the board gone?
Can a power surge damage the dryer control?
Is a mechanical timer easier to repair than a board?
Back to your everyday
Ready to book the dryer control board and moisture sensor repair?
Have these to hand: the code or light pattern on the display, whether cycles end with clothes still damp, whether the buttons respond at all, whether there was a storm or a power outage recently.