Whirlpool dryer
showing F3E2
The control has counted five straight loads that dried without any signal from the moisture strips.
Mon–Sat, 8am–8pm
- Sensor circuit
- Controls and sensors
- Source: Whirlpool
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
What F3E2
actually means.
The control has counted five straight loads that dried without any signal from the moisture strips. Most of the time the clothes simply never touched the strips, because the dryer is out of level or the loads were very small.
Whirlpool dryer display · also shown as F3 E2
What to do when F3E2 shows on the dryerKind of codeSensor circuit
A thermistor or the moisture sensor bars reading outside their range, or the wiring to them. The reading is checked with a meter before any part is ordered.
Usually leads toControls and sensors
A blank display, a panel that ignores buttons, codes, or cycles that end too soon or never end, traced to the board, timer or sensors.
Shows up asDryer Takes Too Long to Dry
Loads that used to dry in one cycle now need two, or come out damp at the seams.
MakeWhirlpool
One of the most common dryer brands in American homes, in electric and gas versions and stacked laundry centers.
SourceWhirlpool product help: F3E2 moisture sensor
Whirlpool dryers with sensor (Automatic) cycles and a two-part code display.
Before you book,
in this order.
Each step comes from Whirlpool's own guidance for F3E2 on its dryers. Follow it to the end: the last card says whether this is a visit.
Press Power to clear F3E2.
Lay a level across the front of the cabinet and adjust the feet until it sits true.
Use Timed Dry for one or two items and larger loads for Automatic cycles.
Book a visit if F3E2 returns with full, level loads.
What not to do
F3E2 is not a heating problem. The dryer may be hot and working; it is the dryness reading that went missing.
What you may
notice with it.
The dryer problems F3E2 tends to arrive with. Answer these at the dryer before anyone is booked.
All problems
Dryer Takes Too Long to Dry
5 causes, cheapest first
Where F3E2 usually leads
Controls and sensors.
Whirlpool
dryers.
One of the most common dryer brands in American homes, in electric and gas versions and stacked laundry centers.
Whirlpool dryer repair
Electric dryer
The most common dryer in US homes: a 240-volt heating coil, a belt-driven drum and a vent to the outside.
Gas dryer
Heat from a burner on natural gas or propane, lit by an igniter and watched over by a flame sensor, with the motor on 120 volts.
Stackable dryer
The dryer half of a stacked pair or a single-frame laundry center, where the height and the closet decide how the repair is done.
In Whirlpool's own words
The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. Whirlpool dryers with sensor (Automatic) cycles and a two-part code display.
Whirlpool F3E2 dryer repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about F3E2.
Can I clear F3E2 myself?
Why would a Whirlpool dryer throw F3E2 after only small loads?
Do the moisture strips on my Whirlpool need cleaning for F3E2?
Back to your everyday
Still showing F3E2?
Book with the code exactly as displayed, the whole model number, and whether you smell burning or gas — for a code, that is where the diagnosis starts.