Miele
Dryer Repair
Compact European dryers, mostly heat-pump models that dry at lower temperatures without an outdoor vent.
Mon–Sat, 8am–8pm
- 2 dryer types
- 6 problems we see
- 8 error codes
Book a visit
Three short steps, about a minute.
or call (844) 314-5837
Loading appointment form…
The appointment form couldn’t load. Please try again.
Miele dryers,
specifically.
Miele's US dryers are 24-inch T1 heat-pump machines that reuse their drying air instead of venting it, and they are often stacked on a Miele washer. They run from an ordinary 120-volt outlet and report problems as F-numbers that Miele's support pages explain one at a time.
The Miele lineupBuilds2 dryer types
Stackable dryer · Ventless dryer
Called out forDryer Takes Too Long to Dry
and 5 more problems on Miele
Repairs we do10 repairs, on any make
Diagnostic visit · Heating element repair · Gas burner and igniter repair · Drum belt and roller repair
Error codesF1 · F3 · F36 · F252 · F53
8 Miele codes with a page of their own
The Miele
lineup.
Miele builds 2 of the 4 dryer types this site covers. Which one decides how the visit is planned.
All dryer typesWhat is particular
to Miele.
The T1 range runs from models such as the TXD160WP to steam-and-fragrance versions like the TXI680WP with SteamFinish and FragranceDos. Knowing which extras a unit carries tells us which parts to bring.
An ordinary household outlet
A T1 model such as the TXI680WP is rated at 120 volts on a 15-amp circuit, not the 240-volt dryer receptacle most US laundry rooms have. A no-power call starts at that outlet and its breaker.
Filters in front of the heat exchanger
Air passes the lint filters in the door opening and then a plinth filter that guards the heat exchanger. When either stage clogs, the dryer asks for airway cleaning or shows F66, and drying slows long before any part fails.
Condensed water has two routes
Water pulled from the load collects in a container or runs through a hose straight to a sink or drain. A kinked hose or a full container brings on the Empty out container light and stops the program.
Sensors in the refrigerant circuit
Because the heat comes from a heat pump, Miele monitors refrigerant temperatures and compressor start-up and gives each its own F-number. Those codes are read before anything is opened, since they narrow the work to one sensor or one circuit.
Parts
Miele parts are model-specific and are ordered against the model and serial number on the rating plate. Heat-pump components are the items most likely to need lead time.
Repair or replace
Heat-pump dryers cost more than vented ones and are chosen for installs where a duct is impractical, so a filter, sensor or door-contact repair nearly always beats replacement. A compressor that will not start on an older unit is the case that deserves a real comparison.
Book your Miele visitWhat we are
called out for.
On Miele, most often dryer takes too long to dry.
All problems
Not a
Miele?
Miele is one of 14 dryer makes on this site. The other 13 each have a page of their own.
All 14 brandsMiele dryer repair,
where we come out.
9 metros, each with its own page.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions about
Miele dryers.
Why does my Miele dryer keep telling me to clean out the airways?
Can a Miele heat-pump dryer drain into a sink instead of the container?
Does a Miele dryer need a 240-volt dryer outlet?
Back to your everyday
Book your Miele visit.
Have the dryer's model number ready — on Miele it decides which parts come on the first visit.